Boiler Refractories - Resco Products

Boilers

The right refractory products used to line boilers play a key role in preventing heat loss and maximizing efficiency. Installing high-quality refractory products improves boiler safety operations and extends life span.

Resco provides high-quality extreme service castable industry-standard refractories. Fully customized solutions help prevent extended downtime and equipment failure. Your Resco Boiler specialist will evaluate the processes and conditions of your boiler.

Evaluating factors including spalling, chemical corrosion, and incorrect installation for improvement. Common signs are fractured or broken refractory tiles, boiler leaks, damaged seal joints, and difficulty maneuvering refractory doors.

Boiler Castable Refractory Products

Boilers require abrasion-resistant castables with the ability to be pumped, casted, or shotcreted. R-MAX PC is the ideal castable with a 70% alumina composition.  Forinsulating castablesQuikLite 3-35PC is an excellent choice for its low installed density and low thermal conductivity. 

Types of Boilers

  • Coal Fired Boilers
  • Natural Gas Fired Boilers
  • Waste-to-Energy Boilers
  • Circulating Fluid Bed Boilers
 
RELATED PRODUCTS
Caulk

22 CaulkArrow icon

22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
Wet Mortar

Adacor 70 DipArrow icon

ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar

Adacor 70 TR-D3.5Arrow icon

ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar

Adacor 80 DipArrow icon

ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar

Adacor 80 TR-D3.5Arrow icon

ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Dry Mortar

Adamant Air Set-DryArrow icon

A dry, air-setting fireclay - silica based mortar, with a maximum service temperature of 3000°F, used for bonding super duty brick. Just add water to obtain the desired trowel or dipping consistency. This product will take an air set, but does not develop its full joint strength until after heating to 220°F (105°C)
A dry, air-setting fireclay - silica based mortar, with a maximum service temperature of 3000°F, used for bonding super duty brick. Just add water to obtain the desired trowel or dipping consistency. This product will take an air set, but does not develop its full joint strength until after heating to 220°F (105°C)
Wet Mortar

Adamant X GreenArrow icon

ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
Wet Mortar

Adaphos 85 DipArrow icon

ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
Wet Mortar

Adaphos 85 TR-D3Arrow icon

ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
Plastic

CorlineArrow icon

CORLINE® was designed for linings exposed to extreme erosion environments in heat enclosures of the oil refining, petrochemical, gas processing and solid fuels processing industries. CORLINE® is a High Alumina, Chemically Bonded, Erosion Resistant Refractory.
CORLINE® was designed for linings exposed to extreme erosion environments in heat enclosures of the oil refining, petrochemical, gas processing and solid fuels processing industries. CORLINE® is a High Alumina, Chemically Bonded, Erosion Resistant Refractory.
CORPATCH® 50-MS is an 50% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
CORPATCH® 50-MS is an 50% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
CORPATCH® 80 is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
CORPATCH® 80 is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
CORPATCH® 80-MS is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
CORPATCH® 80-MS is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
Shotcrete Activator

EZ AddArrow icon

Low Cement Castable

EZ Cast 3400Arrow icon

EZ CAST® 3400 is a self-flowing, 99% alumina, low cement castable for applications up to 3400°F. It has low porosity and low permeability without a sacrifice in thermal shock resistance. This product is not recommended for pumping.
EZ CAST® 3400 is a self-flowing, 99% alumina, low cement castable for applications up to 3400°F. It has low porosity and low permeability without a sacrifice in thermal shock resistance. This product is not recommended for pumping.
Low Cement Castable

EZ Cast 34-10Arrow icon

EZ CAST® 34-10 is a high purity, cement-bonded, alumina-chrome castable that contains 10% chromic oxide. This castable can be used in severe slagging conditions and high temperatures. EZ CAST® 34-10 can be installed using vibration casting, pumping, and shotcreting methods. When shotcreting, RESCO SC-1 is the recommended shotcrete activator.
EZ CAST® 34-10 is a high purity, cement-bonded, alumina-chrome castable that contains 10% chromic oxide. This castable can be used in severe slagging conditions and high temperatures. EZ CAST® 34-10 can be installed using vibration casting, pumping, and shotcreting methods. When shotcreting, RESCO SC-1 is the recommended shotcrete activator.
Low Cement Castable

EZ Cubed 3000Arrow icon

EZ CUBED® 3000 is a Low Cement, 55% Alumina castable that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
EZ CUBED® 3000 is a Low Cement, 55% Alumina castable that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
Low Cement Castable

EZ Cubed 3200 FineArrow icon

A low cement, 75% alumina castable with a maximum service temperature of 3200°F. This castable can be used in a wide variety of refractory applications. The product can be installed by vibration casting, pumping, and shotcreting methods.
A low cement, 75% alumina castable with a maximum service temperature of 3200°F. This castable can be used in a wide variety of refractory applications. The product can be installed by vibration casting, pumping, and shotcreting methods.
Low Cement Castable

EZ Cubed 56SCPCArrow icon

EZ CUBED® 56SCPC is a Low Cement, Silicon Carbide-based castable. This product can be installed by vibration cast, pumping or shotcreting methods.
EZ CUBED® 56SCPC is a Low Cement, Silicon Carbide-based castable. This product can be installed by vibration cast, pumping or shotcreting methods.
Low Cement Castable

EZ Cubed 60 LQYArrow icon

An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack.
An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack.
Low Cement Castable

EZ Cubed 60MArrow icon

Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Low Cement Castable

EZ Cubed 60M XTArrow icon

Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Low Cement Castable

EZ Cubed 80-15Arrow icon

EZ CUBED® 80-15 is a Low Cement, 80% Alumina castable containing a silicon carbide addition that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
EZ CUBED® 80-15 is a Low Cement, 80% Alumina castable containing a silicon carbide addition that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
Low Cement Castable

EZ Cubed 93LCArrow icon

EZ CUBED® 93LC is a Low Cement, 93% Alumina castable with High Abrasion Resistance. This product can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
EZ CUBED® 93LC is a Low Cement, 93% Alumina castable with High Abrasion Resistance. This product can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
Low Cement Castable

EZ Cubed Fine 80 SiCArrow icon

Fine grained/shotcretable/sic containing/low cement castable
Fine grained/shotcretable/sic containing/low cement castable
Low Cement Castable

EZ Cubed Fine 90 BFAArrow icon

Fine grained/shotcretable castable
Fine grained/shotcretable castable
Low Cement Castable

EZ Cubed FS-6PCArrow icon

EZ CUBED® FS-6PC is a Low Cement, Fused Silica-based castable that can be installed by casting methods. This castables features excellent resistance to thermal cycling and low thermal expansion.
EZ CUBED® FS-6PC is a Low Cement, Fused Silica-based castable that can be installed by casting methods. This castables features excellent resistance to thermal cycling and low thermal expansion.
Conventional Castable

EZ Cubed Lo-ErodeArrow icon

EZ CUBED® LO-ERODE® can be vibration cast or poured in addition to shotcreted and can be used at temperatures up to 2600°F. It is a shotcrete mix that will meet the tough property standards at 1500°F required by the hydrocarbon processing industry.
EZ CUBED® LO-ERODE® can be vibration cast or poured in addition to shotcreted and can be used at temperatures up to 2600°F. It is a shotcrete mix that will meet the tough property standards at 1500°F required by the hydrocarbon processing industry.
Chemically Bonded Castables

EZ EST 10CRArrow icon

EZ EST 10CR is a cement-free, alumina-chrome castable with 10% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
EZ EST 10CR is a cement-free, alumina-chrome castable with 10% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
Chemically Bonded Castables

EZ EST 20CRArrow icon

EZ EST 20CR is a cement-free, alumina-chrome castable with 20% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
EZ EST 20CR is a cement-free, alumina-chrome castable with 20% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
Chemically Bonded Castables

EZ EST 32-70 PCArrow icon

EZ EST 32-70 PC is a colloidal-silica bonded, pumpable castable. This product is engineered for short turnaround after placement. The colloidal silica binder must be added as a separate component.
EZ EST 32-70 PC is a colloidal-silica bonded, pumpable castable. This product is engineered for short turnaround after placement. The colloidal silica binder must be added as a separate component.
Chemically Bonded Castables

EZ EST 60GArrow icon

EZ EST 60G is a cement-free, 60% alumina gun mix that can be installed by conventional gunning methods. This product requires an additional liquid binder, called EZ ADD binder, for installation. EZ ADD binder is added at the gunning nozzle during installation
EZ EST 60G is a cement-free, 60% alumina gun mix that can be installed by conventional gunning methods. This product requires an additional liquid binder, called EZ ADD binder, for installation. EZ ADD binder is added at the gunning nozzle during installation
Chemically Bonded Castables

EZ EST 60PCArrow icon

EZ EST 60PC is a cement-free, 60% alumina castable that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation
EZ EST 60PC is a cement-free, 60% alumina castable that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation
Chemically Bonded Castables

EZ EST 60Z PCArrow icon

EZ EST 60Z PC is a colloidal silica-bonded, 60% alumina castable containing zircon that can be vibration cast, pumped, or shotcreted. This castable requires an additional liquid binder (EZ ADD binder) for mixing and installation. Water is NOT added for installation.
EZ EST 60Z PC is a colloidal silica-bonded, 60% alumina castable containing zircon that can be vibration cast, pumped, or shotcreted. This castable requires an additional liquid binder (EZ ADD binder) for mixing and installation. Water is NOT added for installation.
Chemically Bonded Castables

EZ EST 60ZGArrow icon

EZ EST 60ZG is a colloidal-silica bonded gun mix. This product is engineered for short turnaround after placement. The colloidal silica binder must be added at the nozzle. This product also contains an additive to reduce dusting.
EZ EST 60ZG is a colloidal-silica bonded gun mix. This product is engineered for short turnaround after placement. The colloidal silica binder must be added at the nozzle. This product also contains an additive to reduce dusting.
Dry Mortar

Fifty-Fifty MortarArrow icon

FIFTY-FIFTY is a Dry, Heat-Setting, Super Duty Mortar and is available in a dry powder form. When installing, mix with water to desired consistency.
FIFTY-FIFTY is a Dry, Heat-Setting, Super Duty Mortar and is available in a dry powder form. When installing, mix with water to desired consistency.
Pre-Cast Shapes

Gas Panel MixArrow icon

GAS PANEL MIX is used to produce lightweight, strong panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
GAS PANEL MIX is used to produce lightweight, strong panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
Pre-Cast Shapes

Glass Panel MixArrow icon

GLASS PANEL MIX is used to produce lightweight, strong, vermiculite panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
GLASS PANEL MIX is used to produce lightweight, strong, vermiculite panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
Conventional Castable

Hi Strength 25Arrow icon

HI-STRENGTH™ 25 is a very cost-effective, high duty refractory castable designed to resist abrasion and erosion at moderate temperatures. It has excellent thermal shock resistance and is widely used as a refractory lining and maintenance material for many different applications.
HI-STRENGTH™ 25 is a very cost-effective, high duty refractory castable designed to resist abrasion and erosion at moderate temperatures. It has excellent thermal shock resistance and is widely used as a refractory lining and maintenance material for many different applications.
Conventional Castable

Hi Strength 26LIArrow icon

HI-STRENGTH™ 26-LI was developed to meet the demands for a low iron castable in the 125 Ibs/ft3 range. The lower iron content results in better resistance to reducing atmospheres. It has excellent strength throughout its temperature range and very good abrasion and erosion resistance.
HI-STRENGTH™ 26-LI was developed to meet the demands for a low iron castable in the 125 Ibs/ft3 range. The lower iron content results in better resistance to reducing atmospheres. It has excellent strength throughout its temperature range and very good abrasion and erosion resistance.
Conventional Castable

Hi Strength 28LIArrow icon

HI-STRENGTH™ 28-LI produces a tough, monolithic structure with negligible shrinkage. It has good refractoriness with a 2800°F use limit. A casting or ramming consistency may be obtained by control of water during mixing.
HI-STRENGTH™ 28-LI produces a tough, monolithic structure with negligible shrinkage. It has good refractoriness with a 2800°F use limit. A casting or ramming consistency may be obtained by control of water during mixing.
Conventional Castable

HM 26 LIFArrow icon

HM 26 LIF is a Fine Grain, General Purpose Gunning Mix bonded with Low Iron Cement. HM 26 LIF can be used to repair and maintain Coke Oven Walls.
HM 26 LIF is a Fine Grain, General Purpose Gunning Mix bonded with Low Iron Cement. HM 26 LIF can be used to repair and maintain Coke Oven Walls.
Conventional Castable

HM 28 LIArrow icon

HM 28 LI is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60 % mullite content and a low iron calcium aluminate binder.
HM 28 LI is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60 % mullite content and a low iron calcium aluminate binder.
Conventional Castable

HM 28 LI COArrow icon

HM 28LI CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
HM 28LI CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
Conventional Castable

HM 28 LIF COArrow icon

HM 28LIF CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
HM 28LIF CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
Conventional Castable

HM 70Arrow icon

HM 70 is a High Alumina refractory composition bonded with Low Iron Cement. HM 70 is designed for general purpose repairs where there is a need for resistance to high temperatures and erosion.
HM 70 is a High Alumina refractory composition bonded with Low Iron Cement. HM 70 is designed for general purpose repairs where there is a need for resistance to high temperatures and erosion.
Low Cement Castable

Kricon 34-10Arrow icon

KRICON® 34-10 is a chromia-containing, tabular alumina-based castable. The 10% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. It can be used in steel, copper, and other applications requiring excellent corrosion resistance. This castable should be installed using vibration casting methods.
KRICON® 34-10 is a chromia-containing, tabular alumina-based castable. The 10% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. It can be used in steel, copper, and other applications requiring excellent corrosion resistance. This castable should be installed using vibration casting methods.
Low Cement Castable

Kricon 34-5Arrow icon

KRICON® 34-5 is a chromia-containing, tabular alumina-based castable. The 5% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. It can be used in steel, copper, and other applications requiring excellent corrosion resistance.
KRICON® 34-5 is a chromia-containing, tabular alumina-based castable. The 5% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. It can be used in steel, copper, and other applications requiring excellent corrosion resistance.
Low Cement Castable

Kricon CCM-30Arrow icon

KRICON® CCM 30 is a high purity chromia-containing, tabular alumina-based castable. The 30% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. This castable should be installed using vibration casting methods.
KRICON® CCM 30 is a high purity chromia-containing, tabular alumina-based castable. The 30% chromia addition makes this low cement product ideal for high wear areas attacked by slags by improving volume stability and reducing the tendency for the formation of shrinkage cracks at very high temperatures. This castable should be installed using vibration casting methods.
Wet Mortar

Ladlelock 3000 DipArrow icon

LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 TF is an Premium, Air-Setting, Superduty Mortar and is available in a premixed, Troweling consistency.
LADLELOCK 3000 TF is an Premium, Air-Setting, Superduty Mortar and is available in a premixed, Troweling consistency.
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar

Ladlelock 50S DipArrow icon

LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar

Ladlelock 50S Dip-WArrow icon

LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar

Ladlelock 80 DipArrow icon

Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar

Ladlelock 80 Dip-WArrow icon

Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar

Ladlelock 80 TR-D2Arrow icon

Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar

Ladlelock 80 TR-D3Arrow icon

Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar

Ladlelock 85 DipArrow icon

LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
Wet Mortar

Ladlelock 85 Dip-WArrow icon

LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
Wet Mortar

Ladlelock 85 TR-D3Arrow icon

LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
LADLELOCK 90 PBP is a Premium, Phosphate-Bonded, 90% Alumina Mortar and is available in a premixed, Dipping consistency.
LADLELOCK 90 PBP is a Premium, Phosphate-Bonded, 90% Alumina Mortar and is available in a premixed, Dipping consistency.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Insulating Castable

LHV-124Arrow icon

LHV-124 is a lumnite, haydite, and vermiculite (LHV) mix. It is a lightweight, 60 pcf insulating castable that can be installed by casting methods.
LHV-124 is a lumnite, haydite, and vermiculite (LHV) mix. It is a lightweight, 60 pcf insulating castable that can be installed by casting methods.
Wet Mortar

LL 3000 TubesArrow icon

LADLELOCK 3000 IS A HIGH STRENGTH SUPERDUTY AIR SETTING MORTAR.
LADLELOCK 3000 IS A HIGH STRENGTH SUPERDUTY AIR SETTING MORTAR.
LADLELOCK 3000 IS A HIGH STRENGTH SUPERDUTY AIR SETTING MORTAR.
LADLELOCK 3000 IS A HIGH STRENGTH SUPERDUTY AIR SETTING MORTAR.
Conventional Castable

Lo-Erode GMArrow icon

LO-ERODE® GM is an economical, highly effective, abrasion and erosion resistant low iron gunning mix for service temperatures up to 2400°F. When properly gunned, it produces rugged monolithic linings with good volume stability.
LO-ERODE® GM is an economical, highly effective, abrasion and erosion resistant low iron gunning mix for service temperatures up to 2400°F. When properly gunned, it produces rugged monolithic linings with good volume stability.
Dry Mortar

Lo-SetArrow icon

LO-SET® is a 40% alumina mortar with a 3000ºF service temperature limit. When mixed with water, it produces a smooth, easy flowing mortar with good workability. It is air-setting and develops a strong bond at atmospheric temperatures. This bond strength is increased when fired at higher temperatures. Extra service life may be gained by applying a brush or spray coat of LO-SET® on any firebrick surface. Use with high duty, superduty, 50% alumina, and 60% alumina brick.
LO-SET® is a 40% alumina mortar with a 3000ºF service temperature limit. When mixed with water, it produces a smooth, easy flowing mortar with good workability. It is air-setting and develops a strong bond at atmospheric temperatures. This bond strength is increased when fired at higher temperatures. Extra service life may be gained by applying a brush or spray coat of LO-SET® on any firebrick surface. Use with high duty, superduty, 50% alumina, and 60% alumina brick.
Insulating Firebrick

LW 20Arrow icon

2000ºF insulating fire brick
2000ºF insulating fire brick
Insulating Firebrick

LW-20 LIArrow icon

2000ºF insulating fire brick
2000ºF insulating fire brick
Insulating Firebrick

LW-23Arrow icon

2300ºF insulating fire brick
2300ºF insulating fire brick
Insulating Firebrick

LW-23 LIArrow icon

2300ºF insulating fire brick
2300ºF insulating fire brick
Insulating Firebrick

LW-25Arrow icon

2500ºF insulating fire brick
2500ºF insulating fire brick
Insulating Firebrick

LW-26Arrow icon

2600ºF insulating fire brick
2600ºF insulating fire brick
Insulating Firebrick

LW-28Arrow icon

2800ºF insulating fire brick
2800ºF insulating fire brick
Insulating Firebrick

LW-30Arrow icon

3000ºF insulating fire brick
3000ºF insulating fire brick
Insulating Firebrick

LW-32Arrow icon

3200ºF insulating fire brick
3200ºF insulating fire brick
Mineral Refractory

OceaniteArrow icon

Produced from high MgO magnesite, OCEANITE® is a granular refractory which when evenly spread on marine and stationary boiler floors, readily absorbs slag. When cooled, the slag-laden Oceanite® is easily removed with a rake
Produced from high MgO magnesite, OCEANITE® is a granular refractory which when evenly spread on marine and stationary boiler floors, readily absorbs slag. When cooled, the slag-laden Oceanite® is easily removed with a rake
Conventional Castable

Pacocast 24TArrow icon

Pacocast 24T is 40% alumina, low iron castable designed to be more plastic than other conventional castables. This product can be used for patching linings and for installing by troweling or plastering rather than gunning or casting.
Pacocast 24T is 40% alumina, low iron castable designed to be more plastic than other conventional castables. This product can be used for patching linings and for installing by troweling or plastering rather than gunning or casting.
Conventional Castable

Pacocast 28LIArrow icon

PACOCAST 28LI castable combines the qualities of a pyrophyllite/andalusite mineral based composition. It's low iron content makes it ideal for higher temperatures and reducing atmospheres. PACOCAST 28LI should be installed using vibration casting, It is not recommended for gunning use; for gunning see HM-28 LI.
PACOCAST 28LI castable combines the qualities of a pyrophyllite/andalusite mineral based composition. It's low iron content makes it ideal for higher temperatures and reducing atmospheres. PACOCAST 28LI should be installed using vibration casting, It is not recommended for gunning use; for gunning see HM-28 LI.
Conventional Castable

Pacocast 28LI CoarseArrow icon

PACOCAST 28LI COARSE GRAIN offers the qualities of a Pyrophyllite/Andalusite mineral based composition in a coarse grained package. Maximum aggregate size in this product is 1/2 to 3/4 of an inch. Pacocast 28LI Coarse Grain is designed for use in applications where mechanical abuse and impacts are common.
PACOCAST 28LI COARSE GRAIN offers the qualities of a Pyrophyllite/Andalusite mineral based composition in a coarse grained package. Maximum aggregate size in this product is 1/2 to 3/4 of an inch. Pacocast 28LI Coarse Grain is designed for use in applications where mechanical abuse and impacts are common.
Alumina Brick

PatriotArrow icon

Burned fire clay brick
Burned fire clay brick
Alumina Brick

Patriot HFArrow icon

High fired, super duty, carbon monoxide resistant brick
High fired, super duty, carbon monoxide resistant brick
Conventional Castable

ProGun 26LIArrow icon

ProGUN® 26-LI is a conventional mix with less than 2% iron offering excellent performance in service temperatures up to 2600°F
ProGUN® 26-LI is a conventional mix with less than 2% iron offering excellent performance in service temperatures up to 2600°F
Conventional Castable

ProGun 28LIArrow icon

ProGUN® 28-LI is a conventional mix with less than 1% iron offering excellent performance in service temperatures up to 2800°F
ProGUN® 28-LI is a conventional mix with less than 1% iron offering excellent performance in service temperatures up to 2800°F
Conventional Castable

ProGun 30Arrow icon

ProGUN® 30 is a very refractory, reduced cement mix targeted for general service to 3000°F
ProGUN® 30 is a very refractory, reduced cement mix targeted for general service to 3000°F
Low Cement Castable

ProGun LC 28GMArrow icon

ProGUN® LC 28GM is a very refractory, low cement gunning mix targeted for general service to 2800°F
ProGUN® LC 28GM is a very refractory, low cement gunning mix targeted for general service to 2800°F
Low Cement Castable

ProGun LC 30GMArrow icon

ProGUN® LC 30GM is a very refractory, low cement gunning mix targeted for general service to 3000°F
ProGUN® LC 30GM is a very refractory, low cement gunning mix targeted for general service to 3000°F
Low Cement Castable

ProGun LC 50GArrow icon

ProGun LC 50G is a 3000oF low-cement gun mix. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths.
ProGun LC 50G is a 3000oF low-cement gun mix. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths.
Low Cement Castable

ProGun LC 56SCGArrow icon

ProGun LC 56SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
ProGun LC 56SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
Low Cement Castable

ProGun LC 60GArrow icon

ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
Low Cement Castable

ProGun LC 60G (UK)Arrow icon

ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
Low Cement Castable

ProGun LC 60SCG (UK)Arrow icon

ProGun LC 60SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
ProGun LC 60SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
Low Cement Castable

ProGun LC 65SCG (UK)Arrow icon

ProGun LC 65SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
ProGun LC 65SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
Low Cement Castable

ProGun LC 70GArrow icon

ProGun LC 70G is a 3200oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give minimum porosity and low linear change with maximum density and high fired strengths, and can withstand severe high temperature erosive and corrosive environments.
ProGun LC 70G is a 3200oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give minimum porosity and low linear change with maximum density and high fired strengths, and can withstand severe high temperature erosive and corrosive environments.
Low Cement Castable

ProGun LC 70SCG (UK)Arrow icon

ProGun LC 70SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
ProGun LC 70SCG is a SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance, non-wetting characteristics and high heat transfer of SiC make this product an excellent choice for riser lines and pre-heater sections in CEMENT PLANTS and in combustion zones in POWER GENERATION units exclusively. This tightly bonded SiC product greatly reduces (or eliminates) surface slagging and clinker/alkali build-up.
Low Cement Castable

ProGun LC 80SCGArrow icon

ProGun LC 80SCG is an 80% SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the tube walls in the combustion zones of power generating units. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit.
ProGun LC 80SCG is an 80% SiC castable that uses low cement binder technology with the gunite installation method. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the tube walls in the combustion zones of power generating units. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit.
Low Cement Castable

ProGun LC FS-6Arrow icon

ProGun LC FS-6 is a low cement, fused silica gun mix that offers high strength, very good resistance to abrasion, and low reversible thermal expansion.
ProGun LC FS-6 is a low cement, fused silica gun mix that offers high strength, very good resistance to abrasion, and low reversible thermal expansion.
Conventional Castable

Purocast NArrow icon

PUROCAST® N is a 3000°F castable that will withstand rapid heat-up. It is a low iron, high alumina material capable of withstanding reducing or hydrogen atmospheres, carbon deposition, and high sulfur fuels. It has good volume stability, excellent resistance to spalling, and low thermal conductivity.
PUROCAST® N is a 3000°F castable that will withstand rapid heat-up. It is a low iron, high alumina material capable of withstanding reducing or hydrogen atmospheres, carbon deposition, and high sulfur fuels. It has good volume stability, excellent resistance to spalling, and low thermal conductivity.
Insulating Castable

PuroLite 30Arrow icon

PURO-LITE® 30 is a lightweight castable with a very low iron content for service to 3000°F. It can be used in direct exposure to flame or furnace gases, or as a backup for brick or castable. It is a low iron material with good resistance to carbon monoxide disintegration and thermal shock.
PURO-LITE® 30 is a lightweight castable with a very low iron content for service to 3000°F. It can be used in direct exposure to flame or furnace gases, or as a backup for brick or castable. It is a low iron material with good resistance to carbon monoxide disintegration and thermal shock.
Conventional Castable

PuroTabArrow icon

PUROTAB® is a high purity, low iron, high alumina castable designed specifically for use at temperatures up to 3400°F. It is made with tabular alumina aggregate bonded with a high purity calcium aluminate cement. It is highly resistant to reducing atmospheres as well as high sulfur fuels and charge stocks. It has good volume stability with very good resistance to thermal shock
PUROTAB® is a high purity, low iron, high alumina castable designed specifically for use at temperatures up to 3400°F. It is made with tabular alumina aggregate bonded with a high purity calcium aluminate cement. It is highly resistant to reducing atmospheres as well as high sulfur fuels and charge stocks. It has good volume stability with very good resistance to thermal shock
Insulating Castable

QuikLite 3-35PArrow icon

QUIKLITE 3-35P is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35P features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35P can be initially heated without using the traditional ramp-and-hold heatup schedule
QUIKLITE 3-35P is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35P features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35P can be initially heated without using the traditional ramp-and-hold heatup schedule
Insulating Castable

QuikLite 3-35PCArrow icon

QUIKLITE 3-35PC is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35PC features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35PC can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3-35PC is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35PC features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35PC can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QuikLite 3A-DSArrow icon

QUIKLITE 3A-DS is a dust suppressed, lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 3A-DS features a reduced dust level and low iron oxide content. After the initial set, QUIKLITE 3A-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3A-DS is a dust suppressed, lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 3A-DS features a reduced dust level and low iron oxide content. After the initial set, QUIKLITE 3A-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QUIKLITE 3B (UK)Arrow icon

QUIKLITE 3B is a 50 lb/ft2 insulating material that is easily placed by troweling, gunning, or casting and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. This ease of application combined with its good insulating values makes this an ideal choice for heaters, ducts, and other related components.
QUIKLITE 3B is a 50 lb/ft2 insulating material that is easily placed by troweling, gunning, or casting and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. This ease of application combined with its good insulating values makes this an ideal choice for heaters, ducts, and other related components.
Insulating Castable

QUIKLITE 3BLI (UK)Arrow icon

Quiklite 3BLI is a 1400°c low iron insulating material designed for installation by casting or gunning.It is formulated for rapid heatup without using the traditional ramp and hold heating schedule.
Quiklite 3BLI is a 1400°c low iron insulating material designed for installation by casting or gunning.It is formulated for rapid heatup without using the traditional ramp and hold heating schedule.
Insulating Castable

QuikLite 3-DSArrow icon

QUIKLITE 3-DS is a dust suppressed, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, a nominal 60 pcf cast density, and good strength. After the initial set, QUIKLITE 3-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3-DS is a dust suppressed, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, a nominal 60 pcf cast density, and good strength. After the initial set, QUIKLITE 3-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QuikLite 3E-DSArrow icon

QUIKLITE 3E-DS is a special, dust suppressed, lightweight castable formulated for use in the petrochemical industry as a single component lining. This product can be installed by casting or conventional gunning methods. QUIKLITE 3E-DS features a reduced dust level and high strength. After the initial set, QUIKLITE 3E-DS can be initially heated without using the traditional ramp-and-hold heatup schedule. For pumping or shotcreting, QUIKLITE 3E PC is recommended.
QUIKLITE 3E-DS is a special, dust suppressed, lightweight castable formulated for use in the petrochemical industry as a single component lining. This product can be installed by casting or conventional gunning methods. QUIKLITE 3E-DS features a reduced dust level and high strength. After the initial set, QUIKLITE 3E-DS can be initially heated without using the traditional ramp-and-hold heatup schedule. For pumping or shotcreting, QUIKLITE 3E PC is recommended.
Insulating Castable

QuikLite 3PCArrow icon

QUIKLITE 3 PC is a lightweight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3 PC is a lightweight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QuikLite 6Arrow icon

QUIKLITE 6 is a special high strength, medium weight insulating castable formulated primarily for use in the petrochemical industry. This product can be installed by conventional casting or gunning methods. After the initial set, QUIKLITE 6 can be heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 6 is a special high strength, medium weight insulating castable formulated primarily for use in the petrochemical industry. This product can be installed by conventional casting or gunning methods. After the initial set, QUIKLITE 6 can be heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QuikLite 6PCArrow icon

QUIKLITE 6 PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.  
QUIKLITE 6 PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.  
Insulating Castable

QuikLite 7-DSArrow icon

QUIKLITE 7-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 7-DS can be initially heated without using the traditional ramp-and-hold heatup schedule
QUIKLITE 7-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 7-DS can be initially heated without using the traditional ramp-and-hold heatup schedule
Insulating Castable

QuikLite 8-DSArrow icon

QUIKLITE 8-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, good strength, and a low iron content which makes this product suitable for most furnace atmospheres, including CO boilers. After the initial set, QUIKLITE 8-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 8-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, good strength, and a low iron content which makes this product suitable for most furnace atmospheres, including CO boilers. After the initial set, QUIKLITE 8-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QuikLite 8PCArrow icon

QUIKLITE 8PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 8PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable

QUIKLITE 9 (UK)Arrow icon

QUIKLITE 9 is a 2600°F, 90 pcf insulating castable and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. QUIKLITE 9 can be installed by both casting and gunning methods.
QUIKLITE 9 is a 2600°F, 90 pcf insulating castable and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. QUIKLITE 9 can be installed by both casting and gunning methods.
Insulating Castable

QuikLite 9LI-DSArrow icon

QUIKLITE 9LI-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 9LI-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 9LI-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 9LI-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Low Cement Castable

Quikturn 30 SCPCArrow icon

QUIKTURN 30 SCPC is a low cement, high alumina castable containing 35% silicon carbide that can be installed by vibration cast, pumping, and shotcreting methods. This castable was formulated for dust prone, cement preheater applications in the cement industry. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 30 SCPC is a low cement, high alumina castable containing 35% silicon carbide that can be installed by vibration cast, pumping, and shotcreting methods. This castable was formulated for dust prone, cement preheater applications in the cement industry. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

QUIKTURN 30SCG (UK)Arrow icon

QUIKTURN 30 SCPC is a low cement, high alumina castable containing 35% silicon carbide that can be installed by vibration cast, pumping, and shotcreting methods. This castable was formulated for dust prone, cement preheater applications in the cement industry. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 30 SCPC is a low cement, high alumina castable containing 35% silicon carbide that can be installed by vibration cast, pumping, and shotcreting methods. This castable was formulated for dust prone, cement preheater applications in the cement industry. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 32-70Arrow icon

QUIKTURN 32-70 is a low cement, 70% alumina castable that can be installed by vibration cast methods only. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 32-70 is a low cement, 70% alumina castable that can be installed by vibration cast methods only. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 32-70PCArrow icon

QUIKTURN 32-70 PC is a low cement, 70% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 32-70 PC is a low cement, 70% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 45GArrow icon

QUIKTURN 45G is an ultra-low cement, 47% alumina gun mix that is installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 45G is an ultra-low cement, 47% alumina gun mix that is installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 45PCArrow icon

QUIKTURN 45PC is a low cement, 45% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 45PC is a low cement, 45% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Ultra Low Cement

Quikturn 56SCGArrow icon

QUIKTURN 56SCG is a silicon carbide-based, ultra-low cement gun mix that can be installed by conventional dry gunning methods. This product features very good resistance to abrasion and alkali contact along with high thermal conductivity. After the initial set, this gun mix can be heated without using the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for initial heatup.
QUIKTURN 56SCG is a silicon carbide-based, ultra-low cement gun mix that can be installed by conventional dry gunning methods. This product features very good resistance to abrasion and alkali contact along with high thermal conductivity. After the initial set, this gun mix can be heated without using the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for initial heatup.
Low Cement Castable

Quikturn 56SCPCArrow icon

QUIKTURN 56 SCPC is a silicon carbide-based, ultra-low cement castable that can be vibration cast, pumped, or shotcreted. QUIKTURN 56 SCPC has very good resistance to alkali and abrasion along with high thermal conductivity. After the initial set, this unique castable can be heated without using the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for initial heatup.
QUIKTURN 56 SCPC is a silicon carbide-based, ultra-low cement castable that can be vibration cast, pumped, or shotcreted. QUIKTURN 56 SCPC has very good resistance to alkali and abrasion along with high thermal conductivity. After the initial set, this unique castable can be heated without using the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for initial heatup.
Low Cement Castable

Quikturn 60GArrow icon

QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 60G (UK)Arrow icon

QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable

Quikturn 60LQY PCArrow icon

An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule.
An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule.
Alumina Brick

Rescal 10 CRSRArrow icon

Burned, shock resistant, alumina chrome brick
Burned, shock resistant, alumina chrome brick
Alumina Brick

Rescal 70DArrow icon

High alumina brick
High alumina brick
Alumina Brick

Rescal 90 XD-GArrow icon

Burned, high alumina brick
Burned, high alumina brick
Chemically Bonded Castables

Rescobond 3000Arrow icon

RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
Chemically Bonded Castables

Rescobond 3000 (UK)Arrow icon

RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
Chemically Bonded Castables

Rescobond 3000GArrow icon

RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
Chemically Bonded Castables

Rescobond 3000G (UK)Arrow icon

RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
Chemically Bonded Castables

RESCOBOND 60SCG (UK) (Dense)Arrow icon

RESCOBOND 60SCG is a single component phosphate bonded containing 60% silicon carbide. It is a chemically setting refractory gunning mix which develops a quick set and can be heated shortly after installation to provide a fast “back on line” capability for your unit. It’s chemical bonding system provides adherence to existing refractory, making it an effective patching material. RESCOBOND 60SCG can be installed by gunning or hand-packing techniques.
RESCOBOND 60SCG is a single component phosphate bonded containing 60% silicon carbide. It is a chemically setting refractory gunning mix which develops a quick set and can be heated shortly after installation to provide a fast “back on line” capability for your unit. It’s chemical bonding system provides adherence to existing refractory, making it an effective patching material. RESCOBOND 60SCG can be installed by gunning or hand-packing techniques.
Conventional Castable

Rescocast 15GMArrow icon

RESCOCAST 15GM is a 2600°F general duty castable that can be installed by vibration casting methods. It is designed for refractory use in powerplant ash-hopper applications as well as other applications where high strength, moderate abrasion resistance, and medium insulating values are required. RESCOCAST 15GM is also an excellent gunning product that can be troweled too.
RESCOCAST 15GM is a 2600°F general duty castable that can be installed by vibration casting methods. It is designed for refractory use in powerplant ash-hopper applications as well as other applications where high strength, moderate abrasion resistance, and medium insulating values are required. RESCOCAST 15GM is also an excellent gunning product that can be troweled too.
Conventional Castable

Rescocast 17Arrow icon

RESCOCAST 17 is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. It also has erosion resistant properties equal to those in the extreme service group of castables. Good physical properties and ease of application have made it a universally used product throughout all industries where high temperature and high strength are requirements.
RESCOCAST 17 is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. It also has erosion resistant properties equal to those in the extreme service group of castables. Good physical properties and ease of application have made it a universally used product throughout all industries where high temperature and high strength are requirements.
Conventional Castable

Rescocast 17ACArrow icon

RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
Conventional Castable

Rescocast 17AC (UK)Arrow icon

RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
Conventional Castable

Rescocast 17AGArrow icon

RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Conventional Castable

Rescocast 17AG (UK)Arrow icon

RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Conventional Castable

Rescocast 17EGArrow icon

RESCOCAST 17EG is an erosion resistant gunning mix refractory that has been formulated to have improved gunning characteristics and excellent physical properties. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17EG is an erosion resistant gunning mix refractory that has been formulated to have improved gunning characteristics and excellent physical properties. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Conventional Castable

Rescocast 17EG (UK)Arrow icon

RESCOCAST 17EG is an erosion resistant gunning mix refractory that has been formulated to have improved gunning characteristics and excellent physical properties. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17EG is an erosion resistant gunning mix refractory that has been formulated to have improved gunning characteristics and excellent physical properties. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Insulating Castable

Rescocast 3Arrow icon

RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
Insulating Castable

Rescocast 3 (UK)Arrow icon

RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
Insulating Castable

Rescocast 3AArrow icon

RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
Insulating Castable

Rescocast 3A (UK)Arrow icon

RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
Pre-Cast Shapes

Rescocast 3A Panel MixArrow icon

RESCOCAST 3A is a lightweight, low iron, insulating panel mix which has a service limit temperature of 2500oF. It is used primarily where reducing atmospheres may be present.
RESCOCAST 3A is a lightweight, low iron, insulating panel mix which has a service limit temperature of 2500oF. It is used primarily where reducing atmospheres may be present.
Insulating Castable

RESCOCAST 3BArrow icon

RESCOCAST 3B insulating castable is a 50 pcf density castable that can be installed by troweling, casting or conventional gunning methods
RESCOCAST 3B insulating castable is a 50 pcf density castable that can be installed by troweling, casting or conventional gunning methods
Insulating Castable

Rescocast 7Arrow icon

RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
Insulating Castable

Rescocast 7 (UK)Arrow icon

RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
Insulating Castable

Rescocast 8Arrow icon

RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
Insulating Castable

Rescocast 8 (UK)Arrow icon

RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
Insulating Castable

Rescocast 9Arrow icon

RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
Insulating Castable

Rescocast 9 (UK)Arrow icon

RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
Plastic

Rescoram 10CRArrow icon

RESCORAM 10 CR is a high alumina, phosphate-bonded plastic with 10% chromic oxide that is used throughout the metals producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 10 CR is a high alumina, phosphate-bonded plastic with 10% chromic oxide that is used throughout the metals producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic

Rescoram 20CRArrow icon

RESCORAM 20CR is a Phosphate-Bonded Alumina-Chrome Plastic that contains 20% chromic oxide, for increased slag and corrosion resistance.
RESCORAM 20CR is a Phosphate-Bonded Alumina-Chrome Plastic that contains 20% chromic oxide, for increased slag and corrosion resistance.
Plastic

Rescoram 60Arrow icon

RESCORAM 60 is a high alumina, phosphate-bonded plastic that offers excellent resistance to alkali attack. Phosphate bonding allows RESCORAM 60 to develop high strength at lower temperatures.
RESCORAM 60 is a high alumina, phosphate-bonded plastic that offers excellent resistance to alkali attack. Phosphate bonding allows RESCORAM 60 to develop high strength at lower temperatures.
RESCORAM 70 BLUE is a mullite, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics. This product is designed to resist alkali attack.
RESCORAM 70 BLUE is a mullite, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics. This product is designed to resist alkali attack.
Plastic

Rescoram 70SCArrow icon

RESCORAM 70 SC is a 70% silicon carbide, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 70 SC is a 70% silicon carbide, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic

Rescoram 7CRArrow icon

RESCORAM 7 CR is a high alumina, phosphate-bonded plastic with 7% chromic oxide that is used throughout the metals producing industries. RESCORAM 7 CR has a chemical bond that develops a high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 7 CR is a high alumina, phosphate-bonded plastic with 7% chromic oxide that is used throughout the metals producing industries. RESCORAM 7 CR has a chemical bond that develops a high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic

Rescoram 85Arrow icon

RESCORAM 85 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 85 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic

Rescoram 85SArrow icon

Phosphate bonded alumina plastic
Phosphate bonded alumina plastic
Plastic

Rescoram 90Arrow icon

RESCORAM 90 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 90 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic

Rescoram A-45HCArrow icon

Rescoram A-45HC is a super duty, air-setting, plastic refractory that is designed primarily for high temperature boiler service. This product exceeds ASTM standard for PCE 32-1/2.
Rescoram A-45HC is a super duty, air-setting, plastic refractory that is designed primarily for high temperature boiler service. This product exceeds ASTM standard for PCE 32-1/2.
Plastic

Rescoram A-60Arrow icon

RESCORAM A-60 is a high alumina, air-setting, 3100°F service temperature plastic refractory that is used throughout the metals, power, cement, and lime producing industries where higher temperature requirements demand a more refractory material. It is manufactured using Pyrophyllite-Andalusite-Alumina materials which give the product unique long term hot load resistance.
RESCORAM A-60 is a high alumina, air-setting, 3100°F service temperature plastic refractory that is used throughout the metals, power, cement, and lime producing industries where higher temperature requirements demand a more refractory material. It is manufactured using Pyrophyllite-Andalusite-Alumina materials which give the product unique long term hot load resistance.
Plastic

Rescoram A-80Arrow icon

RESCORAM A-80 is a high alumina, air-setting, 3300°F service temperature plastic refractory that is used throughout the metals, power, cement and lime producing industries where higher temperature requirements demand a higher PCE or more refractory material.
RESCORAM A-80 is a high alumina, air-setting, 3300°F service temperature plastic refractory that is used throughout the metals, power, cement and lime producing industries where higher temperature requirements demand a higher PCE or more refractory material.
Plastic

Rescoram A-90Arrow icon

An air setting 90% alumina plastic. This product should be installed by pneumatic ramming.
An air setting 90% alumina plastic. This product should be installed by pneumatic ramming.
Wet Mortar

Rescoset 10CR DipArrow icon

Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Wet Mortar

Rescoset 10CR TR-D3Arrow icon

Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
RESCOSET 3000 is a super duty, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
RESCOSET 3000 is a super duty, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar

Rescoset 50M TR-D3Arrow icon

RESCOSET 50M is a high alumina class, mullite based, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
RESCOSET 50M is a high alumina class, mullite based, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar

Rescoset 80P TR-D3Arrow icon

Rescoset 80P is a wet high alumina bonding mortar with improved shelf life. With the unique chemical bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 80P is primarily used to lay up high alumina brick and is available in troweling and dipping consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 80P is a wet high alumina bonding mortar with improved shelf life. With the unique chemical bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 80P is primarily used to lay up high alumina brick and is available in troweling and dipping consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Wet Mortar

Rescoset 85AS TRArrow icon

Wet, air-setting, 85% alumina bonding mortar with a low silica content
Wet, air-setting, 85% alumina bonding mortar with a low silica content
Wet Mortar

Rescoset 90P TR-D3Arrow icon

Rescoset 90P is a wet high alumina bonding mortar with a chemical bonding system. With the unique bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 90P is primarily used to lay up high alumina brick and is available in troweling consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance
Rescoset 90P is a wet high alumina bonding mortar with a chemical bonding system. With the unique bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 90P is primarily used to lay up high alumina brick and is available in troweling consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance
Wet Mortar

Rescoset MD TRArrow icon

RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar

RESCOSET MD-TR-D4Arrow icon

RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Low Cement Castable

R-Max C (ESC)Arrow icon

R-MAX C is a Abrasion-Resistant, Low Cement 70% Alumina Castable. This castable should be installed by vibration casting only; specifically form vibration.
R-MAX C is a Abrasion-Resistant, Low Cement 70% Alumina Castable. This castable should be installed by vibration casting only; specifically form vibration.
Low Cement Castable

R-Max GArrow icon

R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
Low Cement Castable

R-Max G (ESC)Arrow icon

R-MAX G is a 3200 °F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. RMax G should be installed using conventional gunning methods. The data shown are average test results following the guidelines set forth in ASTM C-903; “Preparing Refractory Concrete Specimens by Cold Gunning”.
R-MAX G is a 3200 °F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. RMax G should be installed using conventional gunning methods. The data shown are average test results following the guidelines set forth in ASTM C-903; “Preparing Refractory Concrete Specimens by Cold Gunning”.
Low Cement Castable

R-Max G (UK)Arrow icon

R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
Low Cement Castable

R-Max G QTArrow icon

R-MAX G QT is a high performance gunning mix designed to provide high abrasion resistance and excellent strengths. R-Max G QT should be installed using conventional gunning methods. After the final set, this unique gun mix can be heated without the traditional controlled heating schedule. Ideal applications for this product include areas of severe abrasion, where refractory heatup is difficult to control or a shorter heatup schedule is desired.
R-MAX G QT is a high performance gunning mix designed to provide high abrasion resistance and excellent strengths. R-Max G QT should be installed using conventional gunning methods. After the final set, this unique gun mix can be heated without the traditional controlled heating schedule. Ideal applications for this product include areas of severe abrasion, where refractory heatup is difficult to control or a shorter heatup schedule is desired.
Low Cement Castable

R-Max PCArrow icon

R-MAX PC is a Pumpable, Abrasion-Resistant, 70% Alumina Castable. This castable can be installed by vibration casting, pumping, or shotcreting methods
R-MAX PC is a Pumpable, Abrasion-Resistant, 70% Alumina Castable. This castable can be installed by vibration casting, pumping, or shotcreting methods
Low Cement Castable

R-Max PC QTArrow icon

R-MAX PC QT is a Pumpable, Abrasion-Resistant, 80% Alumina Castable. This castable can be installed by vibration casting and pumping methods. Ideal applications for this castable are severe abrasion areas where refractory heatup is difficult to control.
R-MAX PC QT is a Pumpable, Abrasion-Resistant, 80% Alumina Castable. This castable can be installed by vibration casting and pumping methods. Ideal applications for this castable are severe abrasion areas where refractory heatup is difficult to control.
Low Cement Castable

R-Max SFArrow icon

A self leveling, 92% alumina castable with maximum erosion resistance, that can installed using the products’s self leveling characteristic or pumpcasting methods. This product should be used in areas subjected to severe abrasion. It is suggested that vibration should not be used during installation since it is a self leveling product.
A self leveling, 92% alumina castable with maximum erosion resistance, that can installed using the products’s self leveling characteristic or pumpcasting methods. This product should be used in areas subjected to severe abrasion. It is suggested that vibration should not be used during installation since it is a self leveling product.
Wet Mortar

Super Adamant TRArrow icon

SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
Low Cement Castable

SUREFLOW 56SC (UK)Arrow icon

Sureflow 56 SC is a silicon carbide based low cement castable specifically designed for installation by self flow casting. Its high thermal conductivity makes it ideal for applications where high heat transfer is important. Sureflow 56 SC shows excellent resistance to abrasion, thermal spalling and corrosion, combined with super high fired strengths.
Sureflow 56 SC is a silicon carbide based low cement castable specifically designed for installation by self flow casting. Its high thermal conductivity makes it ideal for applications where high heat transfer is important. Sureflow 56 SC shows excellent resistance to abrasion, thermal spalling and corrosion, combined with super high fired strengths.
Low Cement Castable

SUREFLOW 70SC (UK)Arrow icon

Sureflow 70SC is a silicon carbide based low cement castable specifically designed for installation by self flow casting. Its high thermal conductivity makes it ideal for applications where high heat transfer is important. Sureflow 70SC shows excellent resistance to abrasion, thermal spalling and corrosion, combined with super high fired strengths.
Sureflow 70SC is a silicon carbide based low cement castable specifically designed for installation by self flow casting. Its high thermal conductivity makes it ideal for applications where high heat transfer is important. Sureflow 70SC shows excellent resistance to abrasion, thermal spalling and corrosion, combined with super high fired strengths.
Low Cement Castable

Vibrocast 2800Arrow icon

VIBROCAST 2800 is an economical 2800°F low cement castable designed to yield high fired strengths at maximum density. This product should be installed by vibration casting methods only.
VIBROCAST 2800 is an economical 2800°F low cement castable designed to yield high fired strengths at maximum density. This product should be installed by vibration casting methods only.
Low Cement Castable

Vibrocast 3000Arrow icon

VIBROCAST 3000 is an economical, Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
VIBROCAST 3000 is an economical, Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable

Vibrocast 50Arrow icon

VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable

Vibrocast 50 (UK)Arrow icon

VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable

Vibrocast 50PCArrow icon

VIBROCAST 50PC is a Pumpable, Low Cement, 45% Alumina castable that can be installed by vibration casting, pumping, and shotcreting methods. It offers excellent resistance to alkalis and requires substantially less vibration than standard low cement castables.
VIBROCAST 50PC is a Pumpable, Low Cement, 45% Alumina castable that can be installed by vibration casting, pumping, and shotcreting methods. It offers excellent resistance to alkalis and requires substantially less vibration than standard low cement castables.
Low Cement Castable

Vibrocast 56SCArrow icon

VIBROCAST 56SC is a SiC castable that uses low cement binder technology. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the combustion zones of POWER GENERATION units and for the riser lines and preheater sections of CEMENT PLANTS. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit. Vibrocast 56SC is best applied by vibration casting.
VIBROCAST 56SC is a SiC castable that uses low cement binder technology. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the combustion zones of POWER GENERATION units and for the riser lines and preheater sections of CEMENT PLANTS. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit. Vibrocast 56SC is best applied by vibration casting.
Low Cement Castable

Vibrocast 60Arrow icon

VIBROCAST 60 is a Mullite-Based, Low Cement, 60% Alumina castable that can be installed by vibration cast methods only.
VIBROCAST 60 is a Mullite-Based, Low Cement, 60% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable

Vibrocast 60PCArrow icon

VIBROCAST 60PC is a Pumpable, Low Cement, 60% Alumina castable based on a mullite aggregate, that can be installed by vibration cast, pumping, and shotcreting methods.
VIBROCAST 60PC is a Pumpable, Low Cement, 60% Alumina castable based on a mullite aggregate, that can be installed by vibration cast, pumping, and shotcreting methods.
Low Cement Castable

Vibrocast 70MArrow icon

VIBROCAST 70M is an economical, low cement 70% alumina with good cast density and high strengths formulated to withstand high temperatures. This product should be installed by vibration casting methods only.
VIBROCAST 70M is an economical, low cement 70% alumina with good cast density and high strengths formulated to withstand high temperatures. This product should be installed by vibration casting methods only.
Low Cement Castable

Vibrocast 80SCArrow icon

VIBROCAST 80SC is an 80% SiC castable that uses low cement binder technology. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the tube walls in the combustion zones of power generating units. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit. VIBROCAST 80SC is best applied by vibrate casting.
VIBROCAST 80SC is an 80% SiC castable that uses low cement binder technology. Its low porosity, excellent abrasion resistance and high heat transfer value make this product an excellent choice for the tube walls in the combustion zones of power generating units. The high heat transfer characteristic of the SiC reduces surface slagging and alkali build-up, thereby, improving the operating efficiency of your unit. VIBROCAST 80SC is best applied by vibrate casting.
Low Cement Castable

Vibrocast FS-6Arrow icon

VIBROCAST FS-6 is a Low Cement, Fused Silica-based Castable that can be installed by vibration cast methods only. This product features excellent resistance to thermal cycling conditions.
VIBROCAST FS-6 is a Low Cement, Fused Silica-based Castable that can be installed by vibration cast methods only. This product features excellent resistance to thermal cycling conditions.